Technical data
- impedance: 6 Ohm
- sensivity (2,83V/1m): 77 dB
- size (HxWxD): 1075 x 180 x 360 mm
- frequency range (-8dB): 22 - 25000 Hz
- crossover frequency(s): 150, 3200 Hz
- speaker type: transmission line
|
Dschinn-TL is a design of Bernd Timmermanns, one of the most famous speaker designers in Germany.
The Heartcore delivers deep bass down to 22 Hz in a compact chassis. The disadvantage: a low efficiency of 77 dB (2,83V, 1m).
For midrange the Tang Band W4-655C is deployed. The bass is provided by a Tang Band 25-1933 S woofer. The Tang Band tweeter 25-1933 S plays above 3200 Hz.
The crossover consists of second-order filters.
The frequency response of the speaker-system is very flat; the decay spectrum is very good.
|
Our kit consists of
- Tang Band tweeter 25-1933
- Tang Band fullrange W4-655, unshielded, with gold colored phase plug
- Tang Band woofer W5-1138 SMF
- Bass reflex tube HP50, 50x145 mm, black
- PE sealing tape, 5x2 mm
- Damping Sonofil 100 x 35 cm for 20 litres
- Audaphon Damping 10, 970 x 470 mm, adhesive
- Binding Post PK31, gold plated (one pair, red and black)
- 5m Speaker cable 2x2.5 mm2, transparent
- Pan screws 4x20 black, cross recess, 12 pieces
- Plan for DIY kit
the crossover components (right),
to be mounted on a piece of wood
|
- Mundorf MCAP EVO 3.9 μF / 450 V
- electrolytic capacitor, etched, 68 μF/100 Vdc
- electrolytic capacitor, etched, 220 μF/63 Vdc
- electrolytic capacitor, etched, 470 μF/63 Vdc
- electrolytic capacitor, unetched, 5.6 μF / 70 Vdc
- electrolytic capacitor, unetched, 68uF / 50 Vdc
- 0.5 mm air core coil, 3.9 mH/3.39 0hm
- 0.5 mm air core coil, 4.7 mH/3.777 0hm
- 0.7 mm air core coil, 0.27 mH/0.44 Ohm
- 0.7 mm air core coil, 15 mH/4,45 Ohm
- Mundorf H core coil H100, 12 mH/0.71 0hm
- Metal-oxide resistor, 5W 2.2 Ohm (red-red-gold)
- Metal-oxide resistor, 5W 3.9 Ohm (orange-white-gold)
- 2x Metal-oxide resistor, 5W 15 Ohm (brown-green-black)
- Metal-oxide resistor, 10W 5.6 Ohm (green-blue-gold)
|
Kit without cabinet, price per speaker
- not available
Kit with high-end crossover
The kit with high-end crossover contains Mundorf coils capacitors in series to the loudspeakers. In series to the woofer a transformer core coil is used. Elsewhere (except L4) baked varnish air core coils are used.
- Mundorf MCAP EVO 68 μF / 350 V
- Mundorf MCAP EVO Oil 3.9 μF / 450 V
- Audaphon MKP CAP Superior 5.6 μF / 400 Vdc
- electrolytic capacitor, etched, 470 μF/63 Vdc
- electrolytic capacitor, unetched, 22uF / 70 Vdc
- electrolytic capacitor, unetched, 68uF / 50 Vdc
- 2x electrolytic capacitor, unetched, 100uF / 50 Vdc
- 0.5 mm Mundorf air core coil, 4.7 mH/3.777 0hm
- Mundorf baked varnish air core coil BL71, 0.27 mH/0.45 Ohm
- Mundorf baked varnish air core coil BL71, 3.9 mH/2.04 Ohm
- Mundorf baked varnish air core coil BL71, 15 mH/4.45 Ohm
- Mundorf bs125 core coil 12mH/0.51Ohm
- Metal-oxide resistor, 5W 2.2 Ohm (red-red-gold)
- Metal-oxide resistor, 5W 5.6 Ohm (green-blue-gold)
- 2x Metal-oxide resistor, 5W 15 Ohm (brown-green-black)
- Metal-oxide resistor, 10W 5.6 Ohm (green-blue-gold)
|
Kit with high-end-crossover without cabinet, price per speaker
- not available
Impedance correction
|
If you want to use a valve amplifier with this speaker an impedance correction should be employed. In this case the component quality is less important; therefore, we offer only one kit (upon request higher quality components are available).
- electrolytic capacitor, unetched, 68uF / 50 Vdc
- electrolytic capacitor, unetched, 82uF / 50 Vdc
- 0.7 mm air core coil, 0.22 mH/0.39 Ohm
- ceramic resistor 5.6 Ohm/20 Watt
Price per impedance correction for one speaker, to be mounted on a small wooden board.
EUR 27,90 excl. VAT: € 23.45 / $ 25.09
universal PCB
If you prefer to mount the crossover components on a 240 x 165 mm universal PCB instead on wood:
Universal PCB RA240, order no.. str-RA240, price per unit:
EUR 8,60 excl. VAT: € 7.23 / $ 7.73
We recommend one board per kit (two boards for a speaker pair)
|