Harwood Stand Up   Floorstanding as in K+T 3/2023

Technical data
  • impedance: 4 Ohm
  • sensivity (2,83V/1m): 84 dB
  • size (HxWxD): 1000 x 232 x 365 mm
  • frequency range (-8dB): 33 - 30000 Hz
  • crossover frequency(s): 120, 3500 Hz
  • speaker type: bass reflex

Harwood Stand Up is a three way floorstanding speaker.

Harwood Stand Up is a bass-reflex cabinet loudspeaker with drivers of Harwood and Scan Speak.

The kit is delivered with the following drivers:
- a Harwood AM 24 air motion transformer (ribbon-tweeter)
- a Harwood TM 130/25F1 mids driver
- a Scan Speak 22W-4534G00 woofer

The loudspeaker has been developed by Thomas Schmidt.

The crossover consists of:
- a 2nd order high-pass filter (12 dB per octave slope) for the tweeter.
- a band pass consisting of a 2nd order high pass filter (12 dB per octave slope) and a 2nd order low-pass filter (12 dB per octave slope) for the mids-woofer.
- a 2nd order low-pass filter (12 dB per octave slope) for the woofer.

The frequency response of this speaker is nearly linear.

The decay spectrum is perfect.

At low volume, i.e. 85 dB at 1 m, the nonlinear distortions are below 0,3% above 300 Hz and doesn't exceed 0,9% at 95 dB at 1 m between 300 and 15000 Hz.

An excerpt from the Klang+Ton review (Translation of the author into English)

Conclusion of the magazine Klang+Ton:

Our kit consists of

  • Harwood Air Motion Transformer AM 24
  • ScanSpeak Woofer 22W-4534G00
  • Harwood TM 130/25F1
  • Bass reflex tube HP70, 70x220m, black
  • 4x Damping fleece MT Bondum 800 (30 x 50 x 2 cm)
  • PE sealing tape, 5x2 mm, 7.5 m
  • 1,5x Damping Sonofil 100 x 35 cm for 20 litres
  • Binding Post PK31, gold plated (one pair, red and black)
  • 3m Speaker cable 2x1.5 mm2, transparent
  • 0,5x Pan screws 3.5x17 black, torx, 8 pieces
  • Pan screws 4x20 black, torx, 8 pieces
  • 0,5x Visaton Countersunk screws 3.5x25, 8 pcs
  • Plan for DIY kit

the crossover components (right),
to be mounted on a small wooden board.

  • Audaphon MKP CAP Superior 3.9 μF / 400 Vdc
  • Audaphon MKP CAP Superior 6.8 μF / 400 Vdc
  • Audaphon MKT CAP 100 μF / 160 Vdc
  • Mundorf, electrolytic capacitor, etched, 680 μF/63 Vdc
  • JB, electrolytic capacitor, bipolar, 150 μF/50 Vdc
  • JB, electrolytic capacitor, bipolar, 220 μF/50 Vdc
  • 1.0 mm air core coil, 1.5 mH/0.63 Ohm
  • 0.7 mm air core coil, 0.47 mH/0.50 Ohm
  • 2x Mundorf H core coil H71, 12 mH/0.98 0hm
  • Mundorf H core coil H100, 12 mH/0.71 0hm
  • ceramic resistor 5.6 Ohm/20 Watt
  • ceramic resistor 8.2 Ohm/20 Watt
  • Metal-oxide resistor, 10W 12 Ohm (brown-red-black)

Kit without cabinet, price per speaker   - not available

Kit with high-end crossover

The high-end kit is delivered with baked varnish air core coils on important parts of the crossover for minimizing microphonic effects. - The current flow through the coil creates a magnetic field which sets the reel of wire in motion. This motion induces a voltage in the coil which adds itself to the signal. The stiffer the reel of wire is, the less the signal will be altered. The capacitors for the Harwood AM 24 are of type polypropylen (MKP) Clarity-Cap CSA 630 V.

  • ClarityCap PWA capacitor 100 μF / 400 Vdc
  • ClarityCap CSA capacitor 3.9 μF / 630 Vdc
  • Audaphon MKP CAP Superior 6.8 μF / 400 Vdc
  • Mundorf, electrolytic capacitor, etched, 680 μF/63 Vdc
  • JB, electrolytic capacitor, bipolar, 150 μF/50 Vdc
  • JB, electrolytic capacitor, bipolar, 220 μF/50 Vdc
  • Mundorf baked varnish air core coil BL71, 0.47 mH/0.57 Ohm
  • Mundorf baked varnish air core coil BL100, 1.5 mH/0.62 Ohm
  • 2x Mundorf H core baked varnish coil BH71, 12 mH/0.98 0hm
  • Mundorf H core baked varnish coil BH125, 12 mH/0.54 0hm
  • ceramic resistor 5.6 Ohm/20 Watt
  • ceramic resistor 8.2 Ohm/20 Watt
  • Metal-oxide resistor, 10W 12 Ohm (brown-red-black)

Kit with high-end-crossover without cabinet, price per speaker   - not available

Impedance correction

If you want to use a valve amplifier with this speaker an impedance correction should be employed. In this case the component quality is less important; therefore, we offer only one kit (upon request higher quality components are available).

  • JB, electrolytic capacitor, bipolar, 68 μF/100 Vdc
  • ceramic resistor 6.8 Ohm/20 Watt

Price per impedance correction for one speaker, to be mounted on a small wooden board.     EUR 4,50 excl. VAT: € 3.78 / $ 4.12

universal PCB

If you prefer to mount the crossover components on a universal PCB instead on wood
PCB 220x155 mm, order no. I-8805002, price per unit:   EUR 11,80 excl. VAT: € 9.92 / $ 10.81
We recommend one board per kit (2 boards per speaker pair)


Home   Klang+Ton Overview