Scan By Side   Floorstanding as in Hobby Hifi 1/2018

Technical data
  • impedance: 4 Ohm
  • sensivity (2,83V/1m): 85 dB
  • size (HxWxD): 1075 x 230 x 380 mm
  • frequency range (-8dB): 28 - 32000 Hz
  • crossover frequency(s): 150, 2700 Hz
  • speaker type: closed box

Scan By Side is a three way floorstanding speaker.

Scan By Side is a closed-cabinet loudspeaker with drivers of SB Acoustics and Scan Speak.

The kit is delivered with the following drivers:
- a Scan Speak D2905/930000 tweeter
- a SB Acoustics SB17NAC35-4 mids driver
- a Scan Speak 26W/4534G00 woofer

The loudspeaker has been developed by Bernd Timmermanns.

The crossover consists of:
- a 2nd order and 3rd order bandpass filter (12 dB per octave slope and 18 dB per octave slope) for the midrange.
- a 2nd order high-pass filter (12 dB per octave slope) for the tweeter.
- a 2nd order low-pass filter (12 dB per octave slope) for the woofer.

The frequency response of this speaker is perfectly linear.

The decay spectrum as shown in the waterfall diagram is exemplary, free of any disturbing resonance.

At medium volume, i.e. 90 dB at 1 m, the nonlinear distortions are below 0,5% above 200 Hz.

Our kit consists of

  • SB Acoustics SB17NAC35-4
  • ScanSpeak tweeter D2905/9300-00
  • ScanSpeak Woofer 26W-4534G00
  • 0,5x Damping 30 1100 x 470 mm, adhesive
  • 0,5x PE sealing tape, 5x2 mm, 7.5 m
  • 2x Damping Sonofil 100 x 35 cm for 20 litres
  • Binding Post PK31, gold plated (one pair, red and black)
  • 4m Speaker cable 2x2.5 mm2, transparent
  • 2x Pan screws 4x20 black, cross recess, 8 pieces
  • Plan for DIY kit

the crossover components (right),
to be mounted on a small wooden board.

  • Audaphon MKP CAP Superior 1.0 μF / 400 Vdc
  • Audaphon MKP CAP Superior 3.9 μF / 400 Vdc
  • electrolytic capacitor, etched, 47 μF/100 Vdc
  • electrolytic capacitor, etched, 100 μF/100 Vdc
  • 2x electrolytic capacitor, etched, 220 μF/63 Vdc
  • electrolytic capacitor, etched, 330 μF/63 Vdc
  • 2x electrolytic capacitor, etched, 470 μF/63 Vdc
  • electrolytic capacitor, unetched, 8.2 μF / 70 Vdc
  • electrolytic capacitor, unetched, 22uF / 70 Vdc
  • 0.7 mm air core coil, 0.56 mH/0.55 Ohm
  • 0.7 mm air core coil, 0.68 mH/0.70 Ohm
  • 0.7 mm air core coil, 0.82 mH/0.89 Ohm
  • 0.7 mm air core coil, 10 mH/3.85 Ohm
  • 0.7 mm air core coil, 18 mH/4,66 Ohm
  • Audaphon M core coil M12, 3.3 mH/0.27 0hm
  • Mundorf bs125 core coil 6.8mH/0.37Ohm
  • Metal-oxide resistor, 10W 1.0 Ohm (brown-black-gold)
  • Metal-oxide resistor, 10W 2.2 Ohm (red-red-gold)
  • Metal-oxide resistor, 10W 4.7 Ohm (yellow-violet-gold)
  • Metal-oxide resistor, 5W 0.47 Ohm 5% (yellow-purple-silver)
  • Metal-oxide resistor, 5W 3.3 Ohm (orange-orange-gold)
  • Metal-oxide resistor, 5W 15 Ohm (brown-green-black)

Kit without cabinet, price per speaker   EUR 591,00 excl. VAT: € 496.64 / $ 541.34

Kit with high-end crossover

The high-end kit is delivered with baked varnish air core coils on important parts of the crossover for minimizing microphonic effects. - The current flow through the coil creates a magnetic field which sets the reel of wire in motion. This motion induces a voltage in the coil which adds itself to the signal. The stiffer the reel of wire is, the less the signal will be altered. The capacitors for the fullrange driver are of type polypropylen (MKP) Mundorf EVO Oil or MKP Cap Superior.

Kit with high-end-crossover without cabinet, price per speaker   EUR 697,00 excl. VAT: € 585.71 / $ 638.43

Impedance correction

If you want to use a valve amplifier with this speaker an impedance correction should be employed. In this case the component quality is less important; therefore, we offer only one kit (upon request higher quality components are available).


Price per impedance correction for one speaker, to be mounted on a small wooden board.     EUR 20,10 excl. VAT: € 16.89 / $ 18.41

universal PCB

If you prefer to mount the crossover components on a 240 x 165 mm universal PCB instead on wood:
Universal PCB RA240, order no.. str-RA240, price per unit:   EUR 8,60 excl. VAT: € 7.23 / $ 7.88
We recommend one board per kit (two boards for a speaker pair)


Home   Hobby HiFi Overview