Staggia Top   Shelf speaker as in K+T 5/2024

Technical data
  • impedance: 6 Ohm
  • sensivity (2,83V/1m): 95 dB
  • size (HxWxD): 920 x 430 x 490 mm
  • frequency range (-8dB): 60 - 23000 Hz
  • crossover frequency(s): 900 Hz
  • speaker type: bass reflex
Enlarge

Staggia Top is a two way compact speaker.

Staggia Top is a bass-reflex cabinet loudspeaker with drivers of Faital Pro .

The kit is delivered with the following drivers:
- a Faital Pro HF 200 + Limmer 250w horn with driver
- a Faital Pro 15HP1030 woofer

The loudspeaker has been developed by Dennis Frank and Daniel Gattig.

The crossover consists of:
- a 3rd order high-pass filter (18 dB per octave slope) for the tweeter.
- a 3rd order low-pass filter (18 dB per octave slope) for the woofer.

The frequency response of this speaker is nearly linear.

The decay spectrum is nearly perfect.

At low volume, i.e. 85 dB at 1 m, the nonlinear distortions are below 2,5% above 100 Hz and doesn't exceed 5% at 95 dB at 1 m between 300 and 15000 Hz.

An excerpt from the Klang+Ton review (Translation of the author into English)

Conclusion of the magazine Klang+Ton:

Our kit consists of

  • Speakon Plug - NL2FXX-W-S
  • Speakon Plug - NL4FXX-W-L
  • Limmer 2 inch - Horn 250w
  • Faital Pro 15 HP 1030 A - 15 inch loudspeaker 1000 W 8 Ohm - Ferrit
  • Faital Pro HF 200 8 Ohm
  • 4x st-BN202278
  • PE sealing tape, 5x2 mm, 7.5 m
  • 2x Damping Sonofil 100 x 35 cm for 20 litres
  • Foam N25, 97,5x49x4 cm, black
  • Neutrik Speakon NL2MP, female, 2 pin
  • 4x Neutrik Speakon NL4MPR, connector round, 4 pin
  • 2m Speaker cable 2x2.5 mm2, transparent
  • 1m 1 m PA speaker cable SPC-525 black
  • 8,5x Pan screws 4x20 black, torx, 8 pieces
  • Allen wood screws, black, 5x30 mm, 8 pieces
  • Plan for DIY kit

the crossover components (right),
to be mounted on a small wooden board.

  • Audaphon MKP CAP Superior 3.9 μF / 400 Vdc
  • Audaphon MKP CAP Superior 6.8 μF / 400 Vdc
  • Audaphon MKP CAP Superior 8.2 μF / 400 Vdc
  • Audaphon MKT CAP 3.9 μF / 160 Vdc
  • Audaphon MKT CAP 5.6 μF / 160 Vdc
  • Audaphon MKT CAP 22 μF / 160 Vdc
  • Audaphon MKT CAP 33 μF / 160 Vdc
  • 1.0 mm air core coil, 1.5 mH/0.63 Ohm
  • 1.4 mm air core coil, 1.0 mH/0.29 Ohm
  • 0.7 mm air core coil, 2.7 mH/1.53 Ohm
  • Mundorf vs140 core coil 1.8 mH/0.14Ohm
  • Mundorf H core coil H71, 6.8 mH/0.7 0hm
  • Mundorf H core coil H71, 8.2 mH/0.8 0hm
  • 2x ceramic resistor 2.7 Ohm/20 Watt
  • ceramic resistor 6.8 Ohm/20 Watt
  • 2x ceramic resistor 10 Ohm/20 Watt
  • ceramic resistor 22 Ohm/20 Watt

Kit without cabinet, price per speaker   EUR 1236,00 excl. VAT: € 1038.66 / $ 1142.52

Kit with high-end crossover

The high-end kit is delivered with baked varnish air core coils on important parts of the crossover for minimizing microphonic effects. - The current flow through the coil creates a magnetic field which sets the reel of wire in motion. This motion induces a voltage in the coil which adds itself to the signal. The stiffer the reel of wire is, the less the signal will be altered. The capacitors for the Faital Pro HF 200 + Limmer 250w are of type polypropylen (MKP) Mundorf MCAP EVO Öl 450 V.

  • Mundorf MCAP EVO Oil 6.8 μF / 450 V
  • Mundorf MCAP EVO Oil 8.2 μF / 450 V
  • 2x Mundorf MKP capacitor 3.9 μF / 250 V
  • Mundorf MKP capacitor 22 μF / 250 V
  • Mundorf MKP capacitor 33 μF / 250 V
  • Mundorf MKP capacitor 5.6 μF / 400 V
  • Mundorf baked varnish air core coil BL71, 2.7 mH/1.53 Ohm
  • Mundorf baked varnish air core coil BL100, 1.5 mH/0.62 Ohm
  • Mundorf baked varnish air core coil BL140, 1.0 mH/0.30 Ohm
  • Mundorf bs180 core coil 1.8 mH/0.09 Ohm
  • Mundorf H core baked varnish coil BH71, 6.8 mH/0.7 0hm
  • Mundorf H core baked varnish coil BH71, 8.2 mH/0.8 0hm
  • ceramic resistor 2.7 Ohm/20 Watt
  • ceramic resistor 6.8 Ohm/20 Watt
  • 2x ceramic resistor 10 Ohm/20 Watt
  • ceramic resistor 22 Ohm/20 Watt
  • MResist Supreme 2.7 Ohm / 20 Watt

Kit with high-end-crossover without cabinet, price per speaker   EUR 1333,00 excl. VAT: € 1120.17 / $ 1232.18

Impedance correction

If you want to use a valve amplifier with this speaker an impedance correction should be employed. In this case the component quality is less important; therefore, we offer only one kit (upon request higher quality components are available).

  • Audaphon MKT CAP 15 μF / 160 Vdc
  • 0.7 mm air core coil, 0.22 mH/0.34 Ohm
  • ceramic resistor 8.2 Ohm/20 Watt

Price per impedance correction for one speaker, to be mounted on a small wooden board.     EUR 11,90 excl. VAT: € 10.00 / $ 11.00

universal PCB

If you prefer to mount the crossover components on a universal PCB instead on wood
PCB 220x155 mm, order no. I-8805002, price per unit:   EUR 11,80 excl. VAT: € 9.92 / $ 10.91
We recommend one board per kit (2 boards per speaker pair)

Measurements

measurmentsMeasurements on this speaker

Home   Klang+Ton Overview