Typ 94   Floorstanding as in K+T 5/2019

Technical data
  • impedance: 4 Ohm
  • sensivity (2,83V/1m): 95 dB
  • size (HxWxD): 978 x 600 x 440 mm
  • frequency range (-8dB): 29 - 26000 Hz
  • crossover frequency(s): 800, 12000 Hz
  • speaker type: bass reflex

Typ 94 is a three way floorstanding speaker.

Typ 94 is a bass-reflex cabinet loudspeaker with drivers of McGee, Kenford and Mivoc.

The kit is delivered with the following drivers:
- a McGee HLQ-02 mit HL-607 horn with driver
- a Kenford COMP 50B mit HL-1018 mids driver
- a Mivoc AWX 184 MK2 woofer

The loudspeaker has been developed by Holger Barske and Thomas Schmidt.

The crossover consists of:
- a 2nd order high-pass filter (12 dB per octave slope) for the tweeter.
- a first order high-pass filter (6 dB per octave slope) for the tweeter.
- a 2nd order low-pass filter (12 dB per octave slope) for the woofer.

The frequency response of this speaker is mostly linear.

The decay spectrum is nearly perfect.

At low volume, i.e. 85 dB at 1 m, the nonlinear distortions are below 1,2% above 200 Hz and doesn't exceed 6% at 105 dB at 1 m between 300 and 15000 Hz.

  • McGee HL-1018
  • McGee HL-607
  • McGee HLQ-02
  • Kenford COMP-50B
  • Mivoc woofer AWX 184 MK2
  • Bass reflex tube for Typ 94
  • PE sealing tape, 5x2 mm, 7.5 m
  • Damping Sonofil 100 x 35 cm for 20 litres
  • 0,5x Foam N25, 100x50x4 cm, black
  • Binding Post PK31, gold plated (one pair, red and black)
  • 3m Speaker cable 2x1.5 mm2 black/red
  • 8x Allen screws M6x40 black, 1 pieces, (IS640)
  • 8x 1 pieces drive-in nuts M6, DIN 6930 g zinc-plated
  • 2,5x Pan screws 4x20 black, torx, 8 pieces
  • Plan for DIY kit

the crossover components (right),
to be mounted on a small wooden board.

  • 2x Audaphon MKP CAP Superior 1.5 μF / 400 Vdc
  • Audaphon MKT CAP 4.7 μF / 160 Vdc
  • electrolytic capacitor, unetched, 47uF / 50 Vdc
  • 0.7 mm air core coil, 0.15 mH/0.28 Ohm
  • Mundorf H core coil H140, 2.7 mH/0.17 0hm
  • 2x ceramic resistor 8.2 Ohm/20 Watt
  • 2x Metal-oxide resistor, 10W 22 Ohm (red-red-black)

Kit without cabinet, price per speaker   - not available

Kit with high-end crossover

The high-end kit is delivered with baked varnish air core coils on important parts of the crossover for minimizing microphonic effects. - The current flow through the coil creates a magnetic field which sets the reel of wire in motion. This motion induces a voltage in the coil which adds itself to the signal. The stiffer the reel of wire is, the less the signal will be altered. The capacitors for the McGee HLQ-02 mit HL-607 are of type polypropylen (MKP) Clarity-Cap ESA 250.

Kit with high-end-crossover without cabinet, price per speaker   - not available

Impedance correction

If you want to use a valve amplifier with this speaker an impedance correction should be employed. In this case the component quality is less important; therefore, we offer only one kit (upon request higher quality components are available).


Price per impedance correction for one speaker, to be mounted on a small wooden board.     EUR 15,00 excl. VAT: € 12.61 / $ 13.36

universal PCB

If you prefer to mount the crossover components on a universal PCB instead on wood
PCB 220x155 mm, order no. I-8805002, price per unit:   EUR 11,80 excl. VAT: € 9.92 / $ 10.51
We recommend one board per kit (2 boards per speaker pair)


Home   Klang+Ton Overview