ViDipol   Floorstanding as in Hobby Hifi 1/2020

Technical data
  • impedance: 6 Ohm
  • sensivity (2,83V/1m): 84,5 dB
  • size (HxWxD): 950 x 280 x 425 mm
  • frequency range (-8dB): 28 - 26000 Hz
  • crossover frequency(s): 500 Hz
  • speaker type: bass reflex

ViDipol is a two way floorstanding speaker.

ViDipol is a bass-reflex cabinet loudspeaker with drivers of Visaton. The fullrange loudspeaker is used as dipol (without closed cabinet).

The kit is delivered with the following drivers:
- a Visaton B 100, 6 Ohm full range driver
- a Visaton TIW 200 XS, 8 Ohm woofer

The loudspeaker has been developed by Bernd Timmermanns.

The crossover consists of:
- a 2nd order high-pass filter (12 dB per octave slope) for the full range driver.
- a 2nd order low-pass filter (12 dB per octave slope) for the woofer.

The frequency response of this speaker is nearly linear.

The decay spectrum is nearly perfect.

At medium volume, i.e. 90 dB at 1 m, the nonlinear distortions are below 1% above 100 Hz.

Our kit consists of

  • Visaton full range driver B 100 - 6 Ohm
  • Visaton woofer TIW 200 XS, 8 Ohm
  • Bass reflex tube BR25.50, black
  • 2x Damping fleece MT Bondum 800 (30 x 50 x 2 cm)
  • 0,5x PE sealing tape, 5x2 mm, 7.5 m
  • 0,5x Audaphon Damping 10, 970 x 470 mm, adhesive
  • Binding Post PK31, gold plated (one pair, red and black)
  • 2m Speaker cable 2x2.5 mm2, transparent
  • 0,5x Pan screws 3.5x17 black, torx, 8 pieces
  • 1,5x Pan screws 4x20 black, torx, 8 pieces
  • Plan for DIY kit

the crossover components (right),
to be mounted on a small wooden board.

  • Mundorf MCAP EVO 0.82 μF; / 450 V
  • ClarityCap PWA capacitor 2.2 μF; / 160 Vdc
  • ClarityCap PWA capacitor 33 μF; / 160 Vdc
  • Mundorf, electrolytic capacitor, unetched, 100uF / 50 Vdc
  • Mundorf air core coil L140, 3.3 mH/0.58 Ohm
  • 1.0 mm air core coil, 2.7 mH/0.90 Ohm
  • 0.7 mm air core coil, 0.82 mH/0.89 Ohm
  • Metal-oxide resistor, 10W 3.9 Ohm (orange-white-gold)
  • Metal-oxide resistor, 10W 4.7 Ohm (yellow-violet-gold)
  • Metal-oxide resistor, 5W 0.33 Ohm 5% (orange-orange-silver)
  • Metal-oxide resistor, 5W 1.5 Ohm (brown-green-gold)

Kit without cabinet, price per speaker   EUR 349,00 excl. VAT: € 293.28 / $ 325.54

Kit with high-end crossover

The high-end kit is delivered with baked varnish air core coils on important parts of the crossover for minimizing microphonic effects. - The current flow through the coil creates a magnetic field which sets the reel of wire in motion. This motion induces a voltage in the coil which adds itself to the signal. The stiffer the reel of wire is, the less the signal will be altered. The capacitors for the Visaton B 100, 6 Ohm are of type polypropylen (MKP) Mundorf EVO ÖL.

Kit with high-end-crossover without cabinet, price per speaker   EUR 437,00 excl. VAT: € 367.23 / $ 407.62

Impedance correction

If you want to use a valve amplifier with this speaker an impedance correction should be employed. In this case the component quality is less important; therefore, we offer only one kit (upon request higher quality components are available).

Price per impedance correction for one speaker, to be mounted on a small wooden board.     EUR 11,45 excl. VAT: € 9.62 / $ 10.68

universal PCB

If you prefer to mount the crossover components on a 159 x 127 mm universal PCB instead on wood:
Universal PCB RA160, order no.. I-2766, price per unit:   EUR 5,10 excl. VAT: € 4.29 / $ 4.76
We recommend one board per kit (two boards for a speaker pair)


Home   Hobby HiFi Overview