WaveLine 152 MK2   Floorstanding as in Hobby Hifi 5/2018

Technical data
  • impedance: 8 Ohm
  • sensivity (2,83V/1m): 82 dB
  • size (HxWxD): 979 x 190 x 280 mm
  • frequency range (-8dB): 32 - 33000 Hz
  • crossover frequency(s): 3000 Hz
  • speaker type: transmission line

Waveline 152 MK2 is a two way floorstanding speaker.

Waveline 152 MK2 is a transmission-line loudspeaker with drivers of Audaphon and Wavecor.

The kit is delivered with the following drivers:
- a Audaphon AMT 2i air motion transformer (ribbon-tweeter)
- a Wavecor WF152CU13 midrange / bass driver

The loudspeaker has been developed by Bernd Timmermanns.

The crossover consists of:
- a 3rd order high-pass filter (18 dB per octave slope) for the tweeter.
- a 3rd order low-pass filter (18 dB per octave slope) for the woofer.

The frequency response of this speaker is perfectly linear.

The decay spectrum as shown in the waterfall diagram is exemplary, free of any disturbing resonance.

At 90 dB and 1 m, nonlinear distortions are below 1 % almost everywhere above 200 Hz.

Our kit consists of

  • Audaphon AMT-2i
  • WF152CU13, Wavecor Mid/Woofer, 8 Ohm, paper / glass fiber, BD, phase plug
  • Damping Sonofil 100 x 35 cm for 20 litres
  • 0,5x Audaphon Damping 10, 970 x 470 mm, adhesive
  • Binding Post PK31, gold plated (one pair, red and black)
  • 2m Speaker cable 2x2.5 mm2, transparent
  • 0,5x Pan screws 3.5x17 black, 8 pieces
  • Plan for DIY kit

the crossover components (right),
to be mounted on a small wooden board.

  • Mundorf MCAP EVO Oil 2.7 μF / 450 V
  • Mundorf MCAP EVO Oil 8.2 μF / 450 V
  • ClarityCap PWA capacitor 33 μF / 160 Vdc
  • Audaphon MKP CAP Superior 10 μF / 400 Vdc
  • Mundorf baked varnish air core coil BL71, 0.27 mH/0.45 Ohm
  • Mundorf baked varnish air core coil BL140, 0.82 mH/0.26 Ohm
  • Mundorf baked varnish air core coil BL140, 1.2 mH/0.34 Ohm
  • Metal-oxide resistor, 10W 3.9 Ohm (orange-white-gold)
  • Metal-oxide resistor, 10W 5.6 Ohm (green-blue-gold)
  • Metal-oxide resistor, 5W 6.8 Ohm (blue-grey-gold)

Kit without cabinet, price per speaker   EUR 721,00 excl. VAT: € 605.88 / $ 660.41

Kit with high-end crossover

The high-end kit is delivered with copper foil air core coils for minimizing microphonic effects. - The current flow through the coil creates a magnetic field which sets the reel of wire in motion. This motion induces a voltage in the coil which adds itself to the signal. The stiffer the reel of wire is, the less the signal will be altered. The capacitors for the tweeter are of type polypropylen (MKP) Mundorf MCAP EVO Silber Gold Öl 450 V.

Kit with high-end-crossover without cabinet, price per speaker   EUR 898,00 excl. VAT: € 754.62 / $ 822.54

Impedance correction

If you want to use a valve amplifier with this speaker an impedance correction should be employed. In this case the component quality is less important; therefore, we offer only one kit (upon request higher quality components are available).


Price per impedance correction for one speaker, to be mounted on a small wooden board.     EUR 27,40 excl. VAT: € 23.03 / $ 25.10

universal PCB

If you prefer to mount the crossover components on a 140 x 102 mm universal PCB instead on wood:
Universal PCB RA140, order no.. str-RA140, price per unit:   EUR 4,20 excl. VAT: € 3.53 / $ 3.85
We recommend two boards per kit (four boards for a speaker pair)


Home   Hobby HiFi Overview