Technical data
- impedance: 4 Ohm
- sensivity (2,83V/1m): 81,5 dB
- size (HxWxD): 280 x 168 x 240 mm
- frequency range (-8dB): 37 - 30000 Hz
- crossover frequency(s): 1600 Hz
- speaker type: bass reflex
|
Wavecor Kit 120-30 is a monitor with premium Wavecor drivers developed by Selmoni Speakers and Cattaneo Acoustics.
The Wavecor Kit 120-30 has an extremely balanced frequency response.
The kit contains a Wavecor dome tweeter TW030WA05 and a Wavecor woofer WF120 BD01.
PDF data sheet
|
Our kit consists of
- Wavecor silk dome tweeter TW030WA05, 4 Ohm
- Wavecor Mid/Woofer WF120BD01, die cast, 4 Ohm
- Bass reflex tube Streamline 30
- Polyester damping material
- 2 pairs Binding Post PK31 (per pair, red and black)
- 1.5m Speaker cable 2x1.5 mm2, transparent
- Pan screws 3.5x17 black, 8 pieces
- Grille circuit board LP/RA160,
- Plan for DIY kit
|
parts for the crossover:
- MKT capacitor 15uF
- MKT capacitor 33uF
- MKP capacitor Q4 10uF / 400V
- 0.7 mm IT air core coil 0.47 mH/0.57 Ohm
- 0.7 mm core coil 1.8 mH/0.80 Ohm
- H40 core coil 1.2 mH/0.15 Ohm
- Corobar coil 0.22 mH
- Ceramic resistor 10 Ohm/5 Watt
- MOX4 resistor 2.2 Ohm/4 Watt (red-red-gold)
- MOX4 resistor 2.7 Ohm/4 Watt (red-purple-gold)
|
Kit without cabinet, price per speaker
EUR 276,00 excl. VAT: € 231.93 / $ 248.17
|
Kit with high-end crossover
In our high-end version only air core coils are used in the signal path to the woofer and in the signal path to the tweeter a Jantzen Z-CAP is employed
- Jantzen Cross Cap MKP capacitor 15 μF / 400V
- Jantzen Cross Cap MKP capacitor 33 μF / 400V
- Jantzen Z-standard MKP capacitor 10 μF / 400V
- Mundorf air core coil L71, 0.47 mH/0.57 Ohm
- Mundorf air core coil L140, 0.22 mH/0.12 Ohm
- Mundorf air core coil L140, 1.2 mH/0.33 Ohm
- 0.7 mm core coil 1.8 mH/0.80 Ohm
- Ceramic resistor 10 Ohm/5 Watt
- MOX4 resistor 2.2 Ohm/4 Watt (red-red-gold)
- MOX4 resistor 2.7 Ohm/4 Watt (red-purple-gold)
Kit with high-end crossover without cabinet, price per speaker
EUR 321,00 excl. VAT: € 269.75 / $ 288.63
Impedance correction
If you want to use a valve amplifier with this speaker an impedance correction should be employed. In this case the component quality is less important; therefore, we offer only one kit (upon request higher quality components are available).
- electrolytic capacitor, etched, 15 μF/100 Vdc
- air core coil L7, 0.56 mH/0.55 Ohm
- MOX4 resistor 5.6 Ohm/4 Watt (green-blue-gold)
Price per impedance correction for one speaker, to be mounted on a small wooden board.
EUR 8,60 excl. VAT: € 7.23 / $ 7.73
|