Cinecor Sub   Subwoofer por K+T 1/2022

Datos técnicos
  • Impedancia: 8 Ohm
  • Nivel de presión sonora (2,83V/1m): aktiv dB
  • Dimensiones (ancho x alto x profundidad): 625 x 625 x 548 mm
  • Rango de frecuencia (-8dB): 18 a 150 Hz
  • Frecuencia (s) Crossover: aktiv Hz
  • Principio: Carcasa cerrada
Agrandar

Cinecor Sub es un subwoofer versátil que presta apoyo a tus altvoces con un bajo potente y profundo .

Cinecor Sub es un altavoz cerrado con chasis fabricado por la empresa Celestion .

El kit incluye un subwoofer Celestion NTR21-5010JD

La columna de altavoz Kura ha sido desarrollada por Thomas Schmidt y Michael Rochow.

La respuesta de frecuencia del altavoz es perfectamente lineal.

Extracto del test de audición de la revista Klang+Ton (Traducción del autor al inglés)

"Judging a subwoofer alone is always a little ungrateful. Rule of thumb: If it is no longer noticeable, it is correctly adjusted. With our Cinecor L box, I had to tinker with it for a long time before the transition fit, because even if the box has a gently roll-off towards the bass, it reaches tremendously deep in the listening room, so that in the end I had to close the reflex tubes to get a clean transition at all. But what then happened dynamically was already an event: music and film material were presented on such a high dynamic level that I couldn't think of anything at first - and believe me: I always find some criticism ... But this is, apart from the infinite power reserves, also in terms of musicality, spatial imaging and yes, also in terms of fine dynamics and attention to detail, a real challenge to the very expensive high-end ready-made speakers. I'm really looking forward to the finished surround set!"

Conclusiones de la revista Klang+Ton:

"Highly dynamic subwoofer that leaves nothing to be desired."

Nuestro kit sin amplificador de montaje se compone de

  • Celestion NTR21-5010JD
  • 0,5x PE sealing tape, 5x2 mm, 7.5 m
  • 0,5x Foam N25-30, 100 x 50 cm, black
  • Binding Post PK28 I, gold plated (one pair, red and black)
  • 1m Speaker cable 2x2.5 mm2, transparent
  • 8x 1 pieces drive-in nuts M6, DIN 6930 g zinc-plated
  • 8x 1 pieces Allen screws M6x50, DIN 912, black
  • Plan for DIY kit

Kit sin la caja, sin la amplificador, precio por altavoz   EUR 719,00 sin IVA: € 604.20 / $ 622.33

El precio de un par de altavoces personalizados con el color deseado.  - No disponible (_)

Kit con amplificador

  • Celestion NTR21-5010JD
  • Hypex FusionAmp FA502
  • 0,5x PE sealing tape, 5x2 mm, 7.5 m
  • 0,5x Foam N25-30, 100 x 50 cm, black
  • 8x 1 pieces drive-in nuts M6, DIN 6930 g zinc-plated
  • 8x 1 pieces Allen screws M6x50, DIN 912, black
  • 1,5x Pan screws 4x20 black, torx, 8 pieces
  • Plan for DIY kit

Kit sin la caja, precio por altavoz   EUR 1346,00 sin IVA: € 1131.09 / $ 1165.03


Atrás   Vista general de las recomendaciones para construcción de la Revista Klang und Ton