Dschinn Mini-TL MTM   Floorstanding as in Hobby Hifi 6/2020

Technical data
  • impedance: 4 Ohm
  • sensivity (2,83V/1m): 89 dB
  • size (HxWxD): 800 x 160 x 272 mm
  • frequency range (-8dB): 48 - 28000 Hz
  • crossover frequency(s): 4000 Hz
  • speaker type: transmission line

Dschinn Mini-TL MTM is a two way floorstanding speaker.

Dschinn Mini-TL exists as two way loudspeaker with woofer-tweeter-woofer arrangement or as two and a half way arrangement with tweeter, midrange loudspeaker and woofer.

Dschinn Mini-TL MTM is a transmission-line loudspeaker with drivers of Omnes Audio and Tang Band.

The kit is delivered with the following drivers:
- a Omnes Audio AMT50 air motion transformer (ribbon-tweeter)
- two Tang Band W4-655 woofers

The loudspeaker has been developed by Bernd Timmermanns.

The crossover consists of:
- a 2nd order high-pass filter (12 dB per octave slope) for the tweeter.
- a 2nd order low-pass filter (12 dB per octave slope) for the mids-woofer.

The frequency response of this speaker is nearly linear.

The decay spectrum is nearly perfect.

At medium volume, i.e. 90 dB at 1 m, the nonlinear distortions are below 0,4% above 300 Hz.

Our kit consists of

  • Omnes Audio AMT 50
  • 2x Tang Band W4-655 C, unshielded
  • Damping fleece MT Bondum 800 (30 x 50 x 2 cm)
  • 0,5x PE sealing tape, 5x2 mm, 7.5 m
  • 0,5x Damping Sonofil 100 x 35 cm for 20 litres
  • Binding Post PK31, gold plated (one pair, red and black)
  • 3m Speaker cable 2x1.5 mm2, transparent
  • 1,5x Pan screws 4x20 black, torx, 8 pieces
  • Plan for DIY kit

the crossover components (right),
to be mounted on a small wooden board.

  • Audaphon MKP CAP Superior 5.6 μF; / 400 Vdc
  • Audaphon MKP CAP Superior 10 μF; / 400 Vdc
  • Mundorf baked varnish air core coil BL71, 0.18 mH/0.34 Ohm
  • Mundorf baked varnish air core coil BL100, 0.82 mH/0.45 Ohm
  • Metal-oxide resistor, 10W 2.2 Ohm (red-red-gold)

Kit without cabinet, price per speaker   EUR 167,00 excl. VAT: € 143.97 / $ 168.44

Kit with high-end crossover

The high-end kit is delivered with baked varnish air core coils on important parts of the crossover for minimizing microphonic effects. - The current flow through the coil creates a magnetic field which sets the reel of wire in motion. This motion induces a voltage in the coil which adds itself to the signal. The stiffer the reel of wire is, the less the signal will be altered. The capacitors for the Omnes Audio AMT50 are of type polypropylen (MKP) Mundorf EVO Öl.

  • Mundorf MCAP EVO Oil 5.6 μF; / 450 V
  • Mundorf MCAP EVO Oil 10 μF; / 450 V
  • Mundorf Hepta Coil II45, 0.18 mH/0.17 Ohm
  • Mundorf baked varnish air core coil BL140, 0.82 mH/0.26 Ohm
  • Mresist Classic 2,2 Ohm / 10 Watt

Kit with high-end-crossover without cabinet, price per speaker   EUR 205,00 excl. VAT: € 176.72 / $ 206.77

Impedance correction

If you want to use a valve amplifier with this speaker an impedance correction should be employed. In this case the component quality is less important; therefore, we offer only one kit (upon request higher quality components are available).

  • Mundorf, electrolytic capacitor, unetched, 33μF / 70 Vdc
  • Mundorf baked varnish air core coil BL71, 0.22 mH/0.34 Ohm
  • ceramic resistor 4.7 Ohm/20 Watt

Price per impedance correction for one speaker, to be mounted on a small wooden board.     EUR 13,99 excl. VAT: € 12.06 / $ 14.11

universal PCB

If you prefer to mount the crossover components on a 140 x 102 mm universal PCB instead on wood:
Universal PCB RA140, order no.. I-2765, price per unit:   EUR 3,61 excl. VAT: € 3.11 / $ 3.64
We recommend one board per kit (two boards for a speaker pair)


Home   Hobby HiFi Overview