Copernicus Subwoofer   Altavoz de pared por K+T 2/2022

Datos técnicos
  • Impedancia: 4 Ohm
  • Nivel de presión sonora (2,83V/1m): aktiv dB
  • Dimensiones (ancho x alto x profundidad): 600 x 600 x 300 mm
  • Rango de frecuencia (-8dB): 25 a 300 Hz
  • Frecuencia (s) Crossover: 300, 2150 Hz
  • Principio: Carcasa cerrada

Copernicus Subwoofer es un subwoofer versátil que presta apoyo a tus altvoces con un bajo potente y profundo .

El Copernicus existe en cinco versiones:

Copernicus Subwoofer es un altavoz cerrado con chasis fabricado por la empresa Wavecor .

El kit incluye un subwoofer Wavecor SW275BD01

La columna de altavoz Kura ha sido desarrollada por Dennis Frank y Daniel Gattig.

El divisor de frecuencia está formado por

Extracto del test de audición de la revista Klang+Ton (Traducción del autor al inglés)

"The Copernicus´ performance with the free-field setting directly in front of the wall is impressing, but in the long run it is clearly too powerful. So I first turned the bass department down by about 6 decibels - that´s better. The impression of infinitely deep and dynamic bass is retained, but it doesn't immediately jump in the listener's face (or stomach). This impression extends over the entire audible frequency range: you can clearly hear that there is significantly more membrane area in every position than with your standard loudspeakers. And because the whole thing is so beautifully linear and without any distortion, you can always get really loud without stressing your ears - very good! When it comes to home cinema, things are going just as well... I caught myself stepping on the gas on the subs for the correct doomsday soundtrack à la "Independance Day" or "2012" - but then that's not entirely possible without worrying about the building´s structural integrity…. "

Conclusiones de la revista Klang+Ton:

" Perfectly tuned wall box with an integrated subwoofer solution that leaves no desires whatsoever. "

"High-end tip"

Nuestro kit de montaje se compone de

  • Wavecor Subwoofer SW275BD01, die cast alu, mica/paper laminated cone, 4 ohm
  • Hypex FusionAmp FA252
  • 3x Damping Sonofil 100 x 35 cm for 20 litres
  • 1,5x Pan screws 4x20 black, torx, 8 pieces
  • Allen wood screws, black, 5x30 mm, 8 pieces
  • Plan for DIY kit

Kit sin la caja, precio por altavoz   EUR 1260,00 sin IVA: € 1058.82 / $ 1143.53

El precio de un par de altavoces personalizados con el color deseado.  EUR 4380,00 sin IVA: € 3680.67 / $ 3975.13

Nuestro kit de montaje se compone de

  • Wavecor Subwoofer SW275BD01, die cast alu, mica/paper laminated cone, 4 ohm
  • 3x Damping Sonofil 100 x 35 cm for 20 litres
  • 2x Binding Post PK28 I, gold plated (one pair, red and black)
  • 2m Speaker cable 2x2.5 mm2 black/red
  • Allen wood screws, black, 5x30 mm, 8 pieces
  • Plan for DIY kit

Kit sin la caja, precio por altavoz   EUR 714,00 sin IVA: € 600.00 / $ 648.00


Atrás   Vista general de las recomendaciones para construcción de la Revista Klang und Ton